Aluminum Dovetail Red Dot Plate for Beretta, 1911, SIG P226, Glock, Springfield XD & S&W M&P – Rear Sight Mount

Dies aluminum dovetail red dot plate lets you mount a micro red dot on a pistol without cutting the slide. The plate replaces the rear sight and locks into the existing rear sight dovetail with a matching clamp bar, giving your optic a flat, low base. Six versions are available: Beretta, 1911, SIG P226, Glock, Springfield XD and S&W M&P. Each one is marked with its plate code, so the right part is easy to identify. Looking for a zinc alloy version? See our pistol red dot mount plate, an, oder durchsuchen Sie alle Leuchtpunktvisierhalterungen.

Why Choose This Aluminum Dovetail Red Dot Plate?

Milling a slide for an optic is permanent and costly. By contrast, a dovetail plate is fully reversible: remove the factory rear sight, fit the plate, and your pistol is ready for a red dot. If you change your mind later, simply refit the original sight.

In addition, every version is cut to the dovetail profile of its pistol. The dimensions for each dovetail are listed below, so you can check the fit before you order.

Key Features of the Dovetail Red Dot Mount Plate

• No slide milling: installs in the existing rear sight dovetail with the supplied clamp bar.
• Six pistol versions: Beretta, 1911, SIG P226, Glock, Springfield XD and S&W M&P.
• Aluminiumkonstruktion: a light, rigid plate with a black finish.
• Marked plate codes: each plate and clamp carries its code (A1/A2 to F1/F2) and pistol name.
• Flaches Profil: keeps the optic close to the slide for a natural sight picture.

Dovetail Red Dot Plate Versions and Dimensions

The table lists the dovetail profile of each version, as shown in the manufacturer’s photos (top width × bottom width × height).

Dovetails can differ between pistol generations and aftermarket slides. Measure your rear sight dovetail and compare it with the table before ordering.

Kompatible Rotpunktvisiere

The plate is designed for micro red dots with the Docter/Noblex-style footprint, such as the Vortex Venom, Vortex Viper and Burris FastFire 3. Because footprints vary, compare the screw spacing of your optic with the plate before installing.

Spezifikationen

Lieferumfang

• 1 × red dot mounting plate (selected version)
• 1 × dovetail clamp bar
• Mounting screws, as pictured

Inbusschlüssel und Rotpunktvisier sind nicht im Lieferumfang enthalten.

How to Install a Dovetail Red Dot Plate

1. Entladen Sie zunächst die Pistole, entfernen Sie das Magazin und bestätigen Sie, dass die Kammer leer ist.
2. Remove the factory rear sight with a sight pusher or punch.
3. Slide the clamp bar into the dovetail, center it, and fit the plate on top.
4. Then tighten the plate screws evenly with a drop of medium thread locker.
5. Finally, mount your red dot on the plate and zero it at the range.

If you do not have a sight pusher, a qualified gunsmith can remove the rear sight for you.

Aluminum Dovetail Red Dot Plate FAQ

Which version do I need?
Choose the version named for your pistol, then check your dovetail against the dimensions table.

What is the difference from your zinc alloy plate?
This version is made from aluminum and adds a SIG P226 option. Both install in the rear sight dovetail.

Kann ich die Eisenvisierung weiterhin verwenden?
The plate replaces the rear sight, so you aim through the red dot once it is installed.

Beretta, Colt, SIG Sauer, Glock, Springfield Armory, Smith & Wesson, Docter, Noblex, Vortex and Burris are trademarks of their respective owners and are used for compatibility reference only. This is an aftermarket accessory and is not affiliated with or endorsed by any of these companies.